Post your Transformers photos - 2011 edition

[chans formers]

"GOING MY WAY?????"

[Dark Rage]

Woah. Custom/KO? Looks like a Knightrider/Black Rodimus.

This is the part where Protoman's supposed to giggle and blush.

[Bruticus82]

Originally Posted by chans formers

"GOING MY WAY?????"

Wow that's just...wow...

Did the original open like that, or did you do that?

[chans formers]

Originally Posted by Bruticus82

Wow that's just...wow...

Did the original open like that, or did you do that?

all of the deluxe classics rodimus have this potential.
but with the new bis 2pac set,it's waaaaaay easier to do.
with the first release roddy,the canopy is translucent "brittle" plastic,dangerous to knock the pin out of it without cracking it and doing the rest of the mods.
but because the bis version is "solid" red plastic,have no fear.
it was nice to see they didn't change the mold design wise,just materials

@darkrage,not k/o,bis roddy,w.i.p. commish for local member mumps,but once i did the canopy mod,i had to shoot it

[Protoman]

OH! MY! GOD!!!!

Now if only it did THIS and had a nice DARK BLUE for the cockpit windows, then CfC/BiS Rodimus would be perfect

[chans formers]

^ummmm.....what's "cfc"?

[The Ark]

Originally Posted by chans formers

^ummmm.....what's "cfc"?

I think it's "Challenge For Cybertron", the 3 pack with white Galvatron.

[Bruticus82]

Originally Posted by chans formers

all of the deluxe classics rodimus have this potential.
but with the new bis 2pac set,it's waaaaaay easier to do.
with the first release roddy,the canopy is translucent "brittle" plastic,dangerous to knock the pin out of it without cracking it and doing the rest of the mods.
but because the bis version is "solid" red plastic,have no fear.
it was nice to see they didn't change the mold design wise,just materials

Is there information on "the rest of the mods" somewhere? I'd be interested in taking a look.

[chans formers]

Originally Posted by The Ark

I think it's "Challenge For Cybertron", the 3 pack with white Galvatron.

aaaaahhhhh,i see

Originally Posted by Bruticus82

Is there information on "the rest of the mods" somewhere? I'd be interested in taking a look.

there used to be a tutorial over on tfw with it but i never did read it.
i basically just winged it and this was the result.
once i can aquire this set locally and it's for myself and not a commish,i'll be sure to do this mod to roddy again,but share more details with pics.now i regret not taking pics along the wip for this bot so far.
a basic text version of how to do it is=

1.remove the flanged screw on the bottom of the car mode that allows the whole canopy to spin around.

2.with the canopy assembly in hand,remove the pin at the back of it,which should give you 2 pieces.(the back trunk middle chunk and the front canopy upper and lower halves)

3.remove the last screw from underneath the canopy and it should seperate like a clam shell.

4.on the 2 grey hinges on the lower half of the canopy,sand the very front and half of the top of them at a 45 degree angle.i used a nail clipper first to speed it up,but keep in mind you want clearance for the canopy lid to pivot,but you still want meat in there as it's a hinge point.

5.on the upper canopy/glass piece,you'll want to remove almost all the plastic on the very rear facing part of it,leaving only an eight of an inch before the roof line.this will give you clearnce so the bottom of the top canopy doesn't smash into the back bottom of the assembly when you open it later on.

6.sand down the very back corners of the upper canopy to add a bit more clearance so that in car mode when you open it,it doesn't catch and scratch your paint job.

you'll also want to sand/round off the upper back lip of the canopy for more clearance.

7.reassemble the pin into the upper/lower/trunk middle piece.

8.very important....do not re-install the screw that's situated behind the seats.only re-install the flanged screw that's under the center console/arm rest.if you install the screw that's behind the seats,it won't open.

9.optional, but if you want to make it so that you don't have to split his hood downwards to open it,at the very front of the canopy,carefully shave it down to the outer shape of the engine on his hood.

hope that helps for now until i aquire this bot again locally

[Dark Rage]

Weren't the interiors custom parts from another toy car though? I'm looking at my Classics Rodimus and it's a bit different from your interior. I'm guessing they changed it a bit for the CfC and BiS versions.